|
| |
INDEPENDENTLY ROTATING FULL ROUND Lazy Susan 6070
SERIES
UPPER PANTRY SHELF SYSTEM
- Locate screw holes with template provided to install bottom
positioner on cabinet floor with four (4) each 3/4" by 8 oval head
screws.
- Locate screw holes with template provided to install upper
pivot support with four (4) each 3/4" by 8 oval head screws.
- Insert bottom end of shaft thru upper shelf and assemble
collar. Repeat for bottom shelf and temporarily tighten collar 6-10 inches
from the bottom of the shaft.
- NOTE: If desired, the lower collar may be discarded to
reduce the height of the lower shelf in the finished installation.
- Tilt the shaft to a horizontal position and ease the
shelves thru the cabinet opening. Raise the shaft to an upright position and
engage the lower end in the bottom positioner. Engage and seat the upper
shaft assembly in the upper pivot support. Tighten the shaft locking screw
and the locking screw in the bottom positioner.
- Space the shelves as desired and tighten the collar(s) with
the locking screws.
INDEPENDENTLY ROTATING
FULL ROUND 6060 SERIES
LOWER PANTRY SHELF SYSTEM |
- Locate screw holes with template provided and
install upper and lower mounting flanges with four (4) each
3/4" by 8 oval head screws. *
- With upper shaft assembly and locking screw
removed from lower shaft assembly, slide collar onto shaft and lock
it in place 6-10 inches from the bottom end of the shaft. Slide
shelf down shaft against collar and add a second collar and shelf.
- Tilt the shaft to a horizontal position and ease
the shelves thru the cabinet opening. (See illustration)
- Raise the shaft to an upright position and rest
the bottom end of the shaft on the cabinet floor behind the
mounting flange.
- Slide another collar onto the shaft.
- With the shaft tilted forward, insert the next
shelf thru the opening and raise and tilt it to a horizontal
position at the top of (and extending out of) the front of the
opening as shown at 3C. Position shaft under shelf and slide shelf
onto shaft. Repeat for the remaining collars and shelves.
- Assemble upper shaft assembly and locking screw
into lower shaft assembly. Lift the lower shaft and engage it in
the lower mounting flange. Engage and seat the upper shaft
assembly in the upper mounting flange and tighten the locking
screw. Tighten the locking screw on the shaft and the locking
screw in the lower mounting flange.
- Space the shelves as desired and tighten the
collars with the locking screws.
- * Mounting flanges are tapped for jack screw
accessory. If used, drill 1" diameter hole through bottom
floor only.
|
 |
Required When Mounting Full Round 6070 Upper
Pantry Shelf System Directly Above 6060 Series Lower Pantry Shelf System
- Using template provided, drill four (4) each 7/32"
diameter holes through the mounting panel.
- Use four (4) each 10-32 by 1" oval head self-tapping
screws to fasten mounting flange to the positioner assembly.
- Locate screw holes with template provided and unstall lower
mounting flange for the Lower Pantry Shelf System with four (4) each
3/4" by 8 oval head screws.*
- Proceed with steps 2-5 of the installation instructions for
the 6060 series Lower Pantry Shelf System.
- Locate screw holes with template provided and install upper
pivot support for the Upper Pantry Shelf System with four (4) each 1/2"
by 8 truss head screws.
- Proceed with steps 3-5 of the installation instructions for
the 6070 Series Upper Pantry Shelf System.
*Mounting flanges are tapped for jack screw accessory. If used, drill
1" diameter hole through bottom floor only.
Should you encounter any problems or have any additional
questions or requirements, please contact
our CUSTOMER SERVICE SPECIALIST at: 1-800-626-1126
|
